Refrigerator ice maker hook up, home guides

If there is no water dispenser, throw away the first full batch or two of ice to make sure it is all clean and ready to use. Disconnect the faucet supply tube from the shutoff valve. Coil the excess water line behind the refrigerator. Although the braided steel is considerably more expensive, the extra strength it provides is well worth the investment.

How to Hook Up a Water Line to a Refrigerator

Twist the male end of a quick-tee adapter onto the valve. Wrap the female thread on the opposite end of the adapter with thread-seal tape. If the refrigerator has a water dispenser, flush out several gallons to purge the line of all the air. Tighten the fittings as needed, using channel-type pliers or an adjustable wrench.

Connect the Supply Tube to the Refrigerator. Thread the ferrule from the kit onto the new line. Run the new supply tube to the back of the refrigerator. Push the refrigerator against the wall.

Twist the faucet supply line onto the female end of the adapter. Turn the water supply valve on and check for leaks. Slip the compression nut that came with the kit over the newly installed supply line. Adapt-A-Tees are easy to install, the rules for dating and they provide the extra line you need with the least amount of work. Slip the remaining compression nut and ferrule over the refrigerator end of the new water line.

Tighten the connections slightly if you see a leak. She has several years of experience in the home-improvement industry, focusing on gardening, and a background in group exercise instruction.

Thread the water line, included in the ice maker installation kit, from the area behind the refrigerator to beneath the sink. You can solve this with an ice maker installation kit that allows you to use the plumbing beneath the sink. If you don't have a convenient water supply pipe and valve near the refrigerator, you must instead find another spot to hook up the water line. The kit provides you with the required parts to hook up a water line to your refrigerator.

How to Install a Water Line for a Refrigerator

How to Install a Water Line for a Refrigerator

How to Hook Up a Water Line to a Refrigerator From the Sink

Refrigerator ice maker hook up

How to Install a Water Line for a Refrigerator Ice Maker

Refrigerator ice maker hook up

Home Guides

Tighten the connection just slightly more than hand-tight, using pliers. If there are no fixure shutoff valves, you can turn off the water by closing the main water supply valve to the entire house. An Adapt-a-Tee is an ideal plumbing fitting for this purpose. Attach the Adapt-a-Tee adapter to the shutoff valve, tightening by hand at first.

Leave the excess water line behind the refrigerator. In most cases, the water line can be run from a kitchen faucet water supply line through the kitchen cabinets and over to the refrigerator. Plug your refrigerator into the wall.

How to Hook Up a Water Line to a Refrigerator From the Sink

Ice maker hookup

You will also need a longer flex water supply tube to run from the water pipe to the refrigerator. Turn the cold water on the supply line clockwise to close it. Shut off the water at the valve that controls the cold-water supply pipe to the faucet.

Tapping the Cold Water Line

HowStuffWorks

Usually, this will be at some other existing water hookup point, blogs like the water supply lines connected to your sink faucet or dishwasher. Turn the supply line on once again. Flex water supply tubes are available in either a tough plastic nylon mesh or braided steel. Insert the new water line into the opening on the tee. Use pliers to untwist the faucet supply line from the cold water supply valve.

  • Adapt-a-Tees can be used in many situations where you need an extra line.
  • Drill as close to the back wall of the cabinet as possible, so you do not lose storage space inside the cabinet.
  • Measure the distance carefully, and buy a supply tube with plenty of length for the job.
  • Running a water line to a refrigerator to supply its ice maker and drinking water dispenser has never been easier.

Drill holes in the base cabinet walls to route the water line from beneath the sink to the rear of the refrigerator. Also, matchmaking services somerset check for leaks where the supply tube connects to the refrigerator before pushing the appliance back into place. Turn on the cold water faucet to drain any water left in the supply line.

Tighten all three nuts on the quick-tee adapter with pliers or an adjustable wrench. They come in various sizes to suit whatever situation you have. The tee adapter connects to the water supply shutoff valve. Disconnect the Existing Water Line.

How to Hook Up a Water Line to a Refrigerator
Refrigerator ice maker hook up
  1. Do not twist the nuts too tight as this could damage the supply valve, the supply line and the adapter.
  2. Now turn on the faucet shutoff valve under the sink and check for leaks at the Adapt-a-Tee connections.
  3. If running the line through the cabinets is not feasible, you might need to run a line through the floor and up to where the refrigerator is located.
  4. If so, your job is very easy.
  5. Find your water supply lines beneath your sink.

She attended Tarrant County College and studied English composition. Connect the line to the water line connector on the back of the refrigerator. Turn the cold water supply valve on beneath the sink.

Watch for leaks at all the connections. First, locate the shutoff valve under the kitchen sink where you want to connect the new water line. She writes mainly home improvement, health and travel articles for various online publications. The valve connected to the right side of the faucet is the cold water supply line.

  • Funny questions to ask someone on a dating site
  • World dating club
  • Pinky savika dating
  • Disadvantages of dating one person exclusively as a teenager
  • 100 percent free uk dating site
  • Legal age difference for dating in missouri
  • Lebanese dating culture
  • Short cute dating quotes
  • Madera dating